Voron 2.4r1 Druckteile (Printed Parts)

CLIPS
• [a]_z_belt_clip_lower_x4.stl
• [a]_z_belt_clip_upper_x4.stl
AB DRIVE UNITS
• a_drive_frame_lower.stl
• a_drive_frame_upper.stl
• b_drive_frame_lower.stl
• b_drive_frame_upper.stl
• [a]_z_chain_retainer_bracket_x2.stl
• [a]_cable_cover.stl
FRONT IDLERS
• front_idler_left_lower.stl
• front_idler_left_upper.stl
• front_idler_right_lower.stl
• front_idler_right_upper.stl
• [a]_tensioner_left.stl
• [a]_tensioner_right.stl
X-CARRIAGE
• blower_housing_rear.stl
• hotend_fan_mount.stl
• probe_retainer_bracket.stl
• x_carriage_frame_left.stl
• x_carriage_frame_right.stl
• x_carriage_pivot_block.stl
• [a]_belt_clamp_x2.stl
• [a]_blower_housing_front.stl
TOOLHEAD
• chain_anchor.stl
• chain_anchor_10x11chains.stl
• extruder_body.stl
• extruder_motor_plate.stl
• latch_shuttle.stl
• [a]_connector_cover.stl
• [a]_guidler.stl
• [a]_latch.stl
XY-JOINTS
• xy_joint_left_lower.stl
• xy_joint_left_upper.stl
• xy_joint_right_lower.stl
• xy_joint_right_upper.stl
• [a]_endstop_pod_hall_effect.stl
• [a]_endstop_pod_microswitch.stl
• [a]_xy_joint_cable_bridge_generic.stl
• [a]_xy_joint_cable_bridge_igus.stl
Z-JOINTS
• z_joint_lower_x4.stl
• z_joint_upper_x4.stl
• z_joint_upper_hall_effect.stl
Z-DRIVE
• z_drive_main_a_x2.stl
• z_drive_main_b_x2.stl
• z_drive_retainer_a_x2.stl
• z_drive_retainer_b_x2.stl
• z_motor_mount_a_x2.stl
• z_motor_mount_b_x2.stl
• z_chain_bottom_anchor.stl
• z_chain_guide.stl
• [a]_belt_tensioner_a_x2.stl
• [a]_belt_tensioner_b_x2.stl
• [a]_z_drive_baseplate_a_x2.stl
• [a]_z_drive_baseplate_b_x2.stl
Z-IDLERS
• z_tensioner_bracket_a_x2.stl
• z_tensioner_bracket_b_x2.stl
• [a]_z_tensioner_x4_9mm.stl
• [a]_z_tensioner_x4_6mm.stl
MISCELLANEOUS
• nozzle_probe.stl
• rail_installation_guide_center_x2.stl
• bowen_retainer.stl
• spool_holder.stl
ELECTRONICS MOUNTING
• plug_panel_filtered_mains.stl
DIN brackets
• lrs_psu_bracket_clip.stl
• raspberrypi_bracket.stl
• rs25_psu_bracket_clip.stl
• pcb_din_clip_x3.stl

Plus Toolhead (E3D v6/ Dragon/ Mosquito) und Board (wie FYSETC Spider, BTT SKR 1.4 oder andere) nach Wahl.
Spider Mod: https://github.com/VoronDesign/VoronUsers/tree/master/printer_mods/hoschi/FYSETC_Spider_DIN_Mount
Octopus Mod: https://github.com/VoronDesign/VoronUsers/tree/master/printer_mods/sse018/Octopus_DIN_Rail_bracket